View NTX2-434650-10_4161256.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EW N
Issue B, 17 March 2005
Radiometrix
Hartcran House, 231 Kenton Lane, Harrow, HA3 8RP, England
Tel: +44 (0) 20 8909 9595, Fax: +44 (0) 20 8909 2233
NTX2/NRX2
UHF Narrow Band FM TX & RX
The NTX2 transmitter and NRX2 receiver offer a low power, reliable data link in a Radiometrix SIL standard pin out and foot print. This makes the NTX2/NRX2 pair ideally suited to those low power applications where existing single frequency wideband UHF modules have insufficient range.
Figure 1: NRX2-434.650-10
NTX2-434.650-10
Features
* * * * * * * Conforms to ETSI EN 300 220-3 (radio) and EN 301 489-3 (EMC) Standard frequencies: 434.075MHz, 434.650MHz and 458.700MHz Custom frequencies available in 433MHz (EU) and 458MHz (UK) band Data rates up to 10kbps Usable range over 500m 25kHz Channel spacing Longer range compared to Wide Band FM modules
Available for licence-exempt operation in the 433MHz (EU) and 458MHz (UK) bands, the NTX2 & NRX2 modules combine effective screening with internal filtering to minimise spurious radiation and susceptibility thereby ensuring EMC compliance. They can be used in existing low data rate (<10kbps) applications where the operating range of the system using TX2 transmitter and RX2 receiver need to be extended. They are particularly suitable for point-to-point and point-to-multipoint wireless links where longer ranges are required at low data rates. Applications include sensor nodes, EPOS and inventory tracking, remote industrial process monitoring, telemetry, telecommand and telecontrol. Because of their small size and low power consumption, both modules are ideal for use in batterypowered portable applications such as handheld terminals. Transmitter - NTX2 * * * * 3 stage crystal controlled VCXO Supply 2.9V - 15V @ 18mA (internal 2.8V voltage regulator) Data bit rate: 10kbps max. Transmit power: +10dBm (10mW)
Receiver - NRX2 * * * * * * * * * * Double conversion FM superhet SAW band pass filter, image rejection: 50dB Intermediate Frequencies (IF): 21.4MHz, 455kHz Supply range: 2.9V - 15V @ 14mA (internal 2.8V voltage regulator) Data bit rate: 10kbps max. Receiver sensitivity: -118dBm (for 12dB SINAD) Receiver sensitivity: -112dBm (for 1ppm BER) Local Oscillator (LO) re-radiation: <-60dBm Adjacent Channel: -70dBm Blocking: -84dB
NTX2/NRX2 data sheet Page 1
Radiometrix Ltd.,
Functional description
The NTX2 transmitter consists of a Frequency Modulated (FM) Voltage Controlled Crystal Oscillator (VCXO) feeding a frequency multiplier with two stage amplifier and RF filter. Operation can be controlled by the EN (Enable) line, the transmitter achieving full RF output typically within 5ms of this line being pulled high. The RF output is filtered to ensure compliance with the appropriate radio regulations and fed to the 50 antenna pin. The NRX2 module is a double conversion NBFM superhet receiver capable of handling data rates of up to 10kbps. It will operate from a supply of 2.9V to 15V and draws 14mA when receiving. A signal strength (RSSI) output with greater than 60dB of range is provided. The SIL style NRX2 measures 47 x 17 x 8 mm excluding the pins.
NTX2 Transmitter
Figure 2: NTX2 block diagram
43mm
32mm
8mm
15mm
NTX2
15.24mm (0.6") 1 2 3 4 5 6 7
23.5mm
7 holes of 0.7mm dia. pin spacing 2.54mm (0.1")
1 = RF gnd 2 = RF out 3 = RF gnd 4 = En 5 = Vcc 6 = 0V 7 = TXD
Figure 3: NTX2 pin-out and dimension User interface NTX2 pin 1, 3 2 4 5 6 7 Notes: 1. 2. 3. EN pin should not be left floating Pinout footprint is as TX1H. Compatible with RX2M, RLC2 and NRX2 Name RF gnd RF out EN Vcc 0V TXD Function RF ground is internally connected to the module screen and pin 6 (0V). These pins should be directly connected to the RF return path - e.g. coax braid, main PCB ground plane etc. 50 RF output to the antenna Pull high to enable Transmitter (3V CMOS logic) 2.9 - 15V DC power supply Ground DC coupled input for 3V CMOS logic. Rin = 100k
Radiometrix Ltd.,
NTX2/NRX2 data sheet
Page 2
NRX2 receiver
Figure 4: NRX2 block diagram
47mm
8mm
17mm
NRX2
Radiometrix
30.48mm (1.2")
1
2
3
4
5
6
7
7 holes of 0.7mm dia pin spacing 2.54mm (0.1")
1 = RF in 2 = RF gnd 3 = RSSI 4 = 0V 5 = Vcc 6 = AF 7 = RXD
Figure 5: NRX2 pin-out and dimension User interface - NRX2
NRX2 pin
1 2 3 4 5 6 7
Name
RF in RF gnd RSSI 0V Vcc AF RXD
Function
50 RF input from the antenna RF Ground is internally connected to the module screen and pin 4 (0V). These pins should be directly connected to the RF return path - e.g. coax braid, main PCB ground plane etc. Received Signal Strength Indicator with >60dB range. DC level between 0.5V and 2V Ground 2.9 - 15V DC power supply 500mVpk-pk audio. DC coupled, approx 0.8V bias Received Data output from the internal data slicer. The data is squared version of the Audio signal on pin 6 and is true data, i.e. as fed to the transmitter. Output is "open-collector" format with internal 10kpull-up to Vcc (pin 5). Suitable for bi-phase codes
Notes: 1. Pinout is as our wideband RX2A receiver
Radiometrix Ltd.,
NTX2/NRX2 data sheet
Page 3
Absolute maximum ratings
Exceeding the values given below may cause permanent damage to the module. Operating temperature Storage temperature NTX2 Vcc, TXD (pins 5,7) En (pin 4) RF out (pin 2) NRX2 Vcc, RXD (pins 7,9) En, RSSI, AF (pins 4,5,8) RF in (pin 1) -10C to +60C -30C to +70C -0.3V to +16.0V -0.3V to +Vcc V 50V @ <10MHz, +20dBm @ >10MHz -0.3V to +16.0V -0.3V to +Vcc V 50V @ <10MHz, +13dBm @ >10MHz
Performance specifications: NTX2 transmitter (Vcc = 3V / temperature = 20C unless stated)
General DC supply Supply voltage TX Supply current Antenna pin impedance RF RF centre frequency NTX2-434.650-10 NTX2-434.075-10 NTX2-458.700-10 Channel spacing Number of channels RF power output Spurious emissions Adjacent channel TX power Frequency accuracy FM deviation (peak) Baseband Modulation type Modulation bandwidth @ -3dB TXD input level (logic low) TXD input level (logic high) Distortion Dynamic timing TX Enable to full RF pin 5 5 2 min. 2.9 434.650 434.075 458.700 25 1 10 -37 3.0 FSK 0 3.0 TBA typ. 3.0 18 50 max. 15 units V mA MHz 1 notes
2 2
9 2.5 0 -
11 -40 2.5 3.5 5 -
kHz dBm dBm dBm kHz kHz 2 3 4 F3D kHz V V % ms 5 5 6
7 7
-
5
Notes: 1. 2. 3. 4. 5. 6.
Available in 25kHz channel steps on other custom frequencies in 433MHz/458MHz band Measured into 50 resistive load. Total over full supply and temperature range. With 0V - 3.0V modulation input. To achieve specified FM deviation. For 1Vpk-pk signal biased at 1.4V
Radiometrix Ltd.,
NTX2/NRX2 data sheet
Page 4
Performance specifications: NRX2 receiver (Vcc = 3V / temperature = 20C unless stated)
pin DC supply Supply voltage Supply current RF/IF RF centre frequency NRX2-434.650-10 NRX2-434.075-10 NRX2-458.700-10 RF sensitivity @ 12dB SINAD RF sensitivity @ 1ppm BER RSSI threshold RSSI range IF bandwidth Blocking Image rejection Adjacent channel rejection Spurious response rejection LO re-radiation Baseband Baseband bandwidth @ -3dB AF level DC offset on AF out Distortion on recovered AF Dynamic timing Power up with signal present Power up to valid RSSI Power up to valid AF Power up to stable data Signal applied with supply on Signal to valid RSSI Signal to valid AF Signal to stable data Time between data transitions 7 7 1,6 434.650 434.075 458.700 -118 -112 -125 55 TBA 84 55 70 55 500 0.8 TBA min. 2.9 typ. 3.0 14 max. 15 units V mA MHz notes
1, 6 1, 7 1, 3 1, 4 1 1 1 1 1 6 6 6 6
0 -
-60 5 -
dBm dBm dBm dB kHz dB dB dB dB dBm kHz mVP-P V %
1 1
2 1 3
5, 3 5,6 5, 7 1, 3 1,6 1, 7 7
0.1
3 2 TBA 2 1 TBA -
10 5 TBA
ms ms ms ms ms ms ms
4
Notes: 1. 2. 3. 4. See applications information for further details. Exceeds EN/EMC requirements at all frequencies. For received signal with 3kHz FM deviation. AF output is inverted with respect to TXD input. For 50:50 mark to space ratio (i.e. squarewave).
Radiometrix Ltd.,
NTX2/NRX2 data sheet
Page 5
Applications information
Power supply requirements Both modules have built-in regulators which deliver a constant 2.8V to the module circuitry when the external supply voltage is 2.9V or greater, with 40dB or more of supply ripple rejection. This ensures constant performance up to the maximum permitted rail, and removes the need for external supply decoupling except in cases where the supply rail is extremely poor (ripple/noise content >100mVpk-pk). The Enable pin allows the TX module to be turned on or off under 3V logic control with a constant DC supply to the Vcc pin. The module current in power-down mode is less than 1A. The Enable pin should be tied directly to the Vcc pin if this facility is not required. TX modulation requirements The module is factory-set to produce the specified FM deviation with a TXD input to pin 7 of 3V amplitude, i.e. 0V "low", 3V "high If the data input level is greater than 3V, a resistor must be added in series with the TXD input to limit the modulating input voltage to a maximum of 3V on pin 7. TXD input resistance is 100k to ground, giving typical required resistor values as follows: Vcc 3V 3.3V 5V 9V Series resistor 10 k 68k 220k
NRX2 Received Signal Strength Indicator (RSSI) The NRX2 receiver incorporates a wide range RSSI which measures the strength of an incoming signal over a range of 55dB or more. This allows assessment of link quality and available margin and is useful when performing range tests. The output on pin 3 of the module has a standing DC bias of <0.5V with no signal, rising to 2V at maximum indication. Typical RSSI characteristic is as shown below:
Figure 6: RSSI response curve
Radiometrix Ltd.,
NTX2/NRX2 data sheet
Page 6
Expected range Predicting the range obtainable in any given situation is notoriously difficult since there are many factors involved. The main ones to consider are as follows: * * * * * Type and location of antennas in use Type of terrain and degree of obstruction of the link path Sources of interference affecting the receiver "Dead" spots caused by signal reflections from nearby conductive objects Data rate and degree of filtering employed
The following are typical examples - but range tests should always be performed before assuming that a particular range can be achieved in a given situation: Data rate 10kbps 10kbps 10kbps Tx antenna 1/4 wave 1/4 wave helical Rx antenna 1/4 wave 1/4 wave helical Environment urban/obstructed Rural/open in-building Range 300m 500m 100m
Data formats and range extension The NTX2's TXD input is normally driven directly by logic levels but will also accept analogue drive (e.g. 2-tone signalling). In this case it is recommended that TXD (pin 7) be DC-biased to 1.2V approx. with the modulation ac-coupled and limited to a maximum of 2Vp-p to minimise distortion over the link. The varactor modulator in the NTX2 introduces some 2nd harmonic distortion which may be reduced if necessary by predistortion of the analogue waveform. Although the modulation bandwidth of the NTX2 extends down to DC as does the NRX2 it is not advisable to use data containing a DC component. This is because frequency errors and drifts between the transmitter and receiver occur in normal operation, resulting in DC offset errors on the NRX2's audio output. The NRX2 in standard form incorporates a low pass filter with a 5kHz nominal bandwidth. In conjunction with similar filtering in the NTX2 an overall system bandwidth of 5kHz is obtained. This is suitable for transmission of data at raw bit rates up to 10kbps.
Radiometrix Ltd.,
NTX2/NRX2 data sheet
Page 7
Antennas
The choice and positioning of transmitter and receiver antennas is of the utmost importance and is the single most significant factor in determining system range. The following notes are intended to assist the user in choosing the most effective antenna type for any given application. Integral antennas These are relatively inefficient compared to the larger externally-mounted types and hence tend to be effective only over limited ranges. They do however result in physically compact equipment and for this reason are often preferred for portable applications. Particular care is required with this type of antenna to achieve optimum results and the following should be taken into account: 1. Nearby conducting objects such as a PCB or battery can cause detuning or screening of the antenna which severely reduces efficiency. Ideally the antenna should stick out from the top of the product and be entirely in the clear, however this is often not desirable for practical/ergonomic reasons and a compromise may need to be reached. If an internal antenna must be used try to keep it away from other metal components and pay particular attention to the "hot" end (i.e. the far end) as this is generally the most susceptible to detuning. The space around the antenna is as important as the antenna itself. 2. Microprocessors and microcontrollers tend to radiate significant amounts of radio frequency hash which can cause desensitisation of the receiver if its antenna is in close proximity. The problem becomes worse as logic speeds increase, because fast logic edges generate harmonics across the UHF range which are then radiated effectively by the PCB tracking. In extreme cases system range may be reduced by a factor of 5 or more. To minimise any adverse effects situate antenna and module as far as possible from any such circuitry and keep PCB track lengths to the minimum possible. A ground plane can be highly effective in cutting radiated interference and its use is strongly recommended. A simple test for interference is to monitor the receiver RSSI output voltage, which should be the same regardless of whether the microcontroller or other logic circuitry is running or in reset. The following types of integral antenna are in common use: Quarter-wave whip. This consists simply of a piece of wire or rod connected to the module at one end. At 434MHz the total length should be 164mm from module pin to antenna tip including any interconnecting wire or tracking. Because of the length of this antenna it is almost always external to the product casing. Helical. This is a more compact but slightly less effective antenna formed from a coil of wire. It is very efficient for its size, but because of its high Q it suffers badly from detuning caused by proximity to nearby conductive objects and needs to be carefully trimmed for best performance in a given situation. The size shown is about the maximum commonly used at 434MHz and appropriate scaling of length, diameter and number of turns can make individual designs much smaller. Loop. A loop of PCB track having an inside area as large as possible (minimum about 4cm2), tuned and matched with 2 capacitors. Loops are relatively inefficient but have good immunity to proximity detuning, so may be preferred in shorter range applications where high component packing density is necessary. Integral antenna summary: whip *** *** * ** helical ** ** *** * loop * * ** ***
Ultimate performance Ease of design set-up Size Immunity to proximity effects
Radiometrix Ltd.,
NTX2/NRX2 data sheet
Page 8
0.5 mm enameled copper wire close wound on 3.2 mm diameter former
RF
433 MHz = 24 turns
A. Helical antenna
Feed point 15% to 25% of total loop length
RF-GND
C2 C3 C4 C1
track width = 1mm 4 to 10 cm inside area
2
RF
B. Loop antenna
16.4cm
wire, rod, PCB-track or a combination of these three
RF
C. Whip antenna
433 MHz = 16.4 cm total from RF pin.
Figure 7: integral antenna configurations
External antennas These have several advantages if portability is not an issue, and are essential for long range links. External antennas can be optimised for individual circumstances and may be mounted in relatively good RF locations away from sources of interference, being connected to the equipment by coax feeder. Helical. Of similar dimensions and performance to the integral type mentioned above, commerciallyavailable helical antennas normally have the coil element protected by a plastic moulding or sleeve and incorporate a coax connector at one end (usually a straight or right-angle BNC/SMA type). These are compact and simple to use as they come pre-tuned for a given application, but are relatively inefficient and are best suited to shorter ranges. Quarter-wave whip. Again similar to the integral type, the element usually consists of a stainless steel rod or a wire contained within a semi-flexible moulded plastic jacket. Various mounting options are available, from a simple BNC/SMA connector to wall brackets, through-panel fixings and magnetic mounts for temporary attachment to steel surfaces. A significant improvement in performance is obtainable if the whip is used in conjunction with a metal ground plane. For best results this should extend all round the base of the whip out to a radius of the length of the whip used (under these conditions performance approaches that of a half-wave dipole) but even relatively small metal areas will produce a worthwhile improvement over the whip alone. The ground plane should be electrically connected to the coax outer at the base of the whip. Magnetic mounts are slightly different in that they rely on capacitance between the mount and the metal surface to achieve the same result. A ground plane can also be simulated by using 3 or 4 quarter-wave radials equally spaced around the base of the whip, connected at their inner ends to the outer of the coax feed. A better match to a 50 coax feed can be achieved if the elements are angled downwards at approximately 30-40 to the horizontal.
Radiometrix Ltd.,
NTX2/NRX2 data sheet
Page 9
Module mounting considerations The modules may be mounted vertically or bent horizontal to the motherboard. Note that the components mounted on the underside of the NTX2 and NRX2 are relatively fragile - avoid direct mechanical contact between these and other parts of the equipment if possible, particularly in situations where extreme mechanical stresses could routinely occur (as a result of equipment being dropped onto the floor, etc). Good RF layout practice should be observed. 50 microstrip line or coax or a combination of both should be used to connect RF pin of the module to RF connector or antenna. It is desirable (but not essential) to fill all unused PCB area around the module with ground plane. Variants and ordering information The NTX2 transmitters and NRX2 receivers are manufactured in the following variants as standard: At 434.650MHz: At 434.075MHz: At 458.700MHz: NTX2-434.65-10 - Transmitter NRX2-434.65-10 - Receiver NTX2-434.075-10 - Transmitter NRX2-434.075-10 - Receiver NTX2-458.700-10 - Transmitter NRX2-458.700-10 - Receiver
Other frequency variants can be supplied to individual customer requirements in the 433MHz (European) and 458MHz (UK) licence exempt bands
Radiometrix Ltd.,
NTX2/NRX2 data sheet
Page 10
Radiometrix Ltd
Hartcran House 231 Kenton Lane Harrow, Middlesex HA3 8RP ENGLAND Tel: +44 (0) 20 8909 9595 Fax: +44 (0) 20 8909 2233 sales@radiometrix.com www.radiometrix.com Copyright notice
This product data sheet is the original work and copyrighted property of Radiometrix Ltd. Reproduction in whole or in part must give clear acknowledgement to the copyright owner.
Limitation of liability
The information furnished by Radiometrix Ltd is believed to be accurate and reliable. Radiometrix Ltd reserves the right to make changes or improvements in the design, specification or manufacture of its subassembly products without notice. Radiometrix Ltd does not assume any liability arising from the application or use of any product or circuit described herein, nor for any infringements of patents or other rights of third parties which may result from the use of its products. This data sheet neither states nor implies warranty of any kind, including fitness for any particular application. These radio devices may be subject to radio interference and may not function as intended if interference is present. We do NOT recommend their use for life critical applications. The Intrastat commodity code for all our modules is: 8542 6000
R&TTE Directive
After 7 April 2001 the manufacturer can only place finished product on the market under the provisions of the R&TTE Directive. Equipment within the scope of the R&TTE Directive may demonstrate compliance to the essential requirements specified in Article 3 of the Directive, as appropriate to the particular equipment. Further details are available on The Office of Communications (Ofcom) web site: http://www.ofcom.org.uk/radiocomms/ifi/ Information Requests Ofcom Riverside House 2a Southwark Bridge Road London SE1 9HA Tel: +44 (0)845 456 3000 or 020 7981 3040 Fax: +44 (0)20 7783 4033 information.requests@ofcom.org.uk European Radiocommunications Office (ERO) Peblingehus Nansensgade 19 DK 1366 Copenhagen Tel. +45 33896300 Fax +45 33896330 ero@ero.dk www.ero.dk

▲Up To Search▲

Price & Availability of NTX2-434650-10

	To Download NTX2-434650-10 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .